nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)
      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)
      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)
      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)
      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)

      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)

      WS-15951
      €28.68

      23.90 € tax excl.

      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)

      Quantity :
      OUT OF STOCK

      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)

      nRF52840 Bluetooth 5.0 Evaluation Kit, Arduino / Raspberry Pi Connectivity

      Only one NRF52840 module is included in the kit, it should be noted that at least three NRF52840 modules are required for Bluetooth MESH networking.

      Overview

      NRF52840 Eval Kit is a development/evaluation kit based on nRF52840, features Arduino / Raspberry Pi connectivity, and several common used peripherals.

      It supports the new generation Bluetooth 5.0, compared to Bluetooth 4.0, the data rate is twice, up to 2Mbps, the transfer distance is quadruple. Based on the ARM Cortex-M4F architecture, the CPU frequency achieves up to 64MHz. Bluetooth MESH and 2.4GHz radio are also available, that means higher performance, and more suitable applications.

      Thanks to the onboard Arduino / Raspberry Pi compatible headers, both Arduino shields and Raspberry Pi HATs can be attached at the same time, make it easy to use more expansion resources.

      Features

      • Arduino connectivity, supports Arduino shields
      • Raspberry Pi connectivity, supports Raspberry Pi HATs
      • Integrates CP2102 USB TO UART, for serial debugging
      • Onboard several peripherals and interfaces, convenient for study / development
      • Comes with development resources and manual (examples for Bluetooth 5.0 / Bluetooth MESH)

      What's on Board

      NRF52840 Eval Kit on board resource

      1. Arduino headers: for connecting Arduino shields
      2. Raspberry Pi GPIO header: for connecting Raspberry Pi HATs
      3. USB TO UART interface
      4. USB port: the USB port of nRF52840
      5. 4PIN SWD debugging interface: for connecting ARM Debugger to program / debug
      6. 3.3V/5V power input/output: provides power output OR powered from external power supply
      7. Core52840: nRF52840 core module
      8. CP2102: USB TO UART converter
      9. Buzzer
      10. RT9193-33: 3.3V voltage regulator
      11. Optical sensor
      12. Keys: RESET and USER KEY
      13. LEDs
        PWR: power indicator
        RXD/TXD: nRF52840 UART RX/TX indicator
        LED1~LED4: USER LEDs
      14. Power switch
        USB: powered from USB connection
        Battery: powered from CR2032 battery
      15. NFC antenna connector
      16. TF card slot
      17. CR2032 battery holder
      18. Jumpers
        Short the jumpers: connect the onboard peripherals to I/Os in example code
        Open the jumpers: connect to custom I/Os via jumper wires
      19. Current testing pads: 0Ω resistor is soldered by default, remove the resistor to test current of the board

      Core52840 Specifications

      • Onboard chip: nRF52840
      • Communication distance: 150m (open outdoor), 40m (indoor)
      • Data rate: 2Mbps, 1Mbps, 500kbps, 125kbps
      • Frequency range: 2.4GHz
      • Operating voltage: 2.0V ~ 3.6V (3.0V recommended)
      • Operating temperature: -40℃ ~ 85℃
      • Storage temperature: -55℃ ~ 125℃
      • Dimension: 18mm × 13.5mm
      • Antenna: onboard antenna

      nRF52840 Features

      nRF52840 is an ultra-low power, flexible wireless system on chip (SoC), it is the ideal choice for short range wireless applications such as wearable devices, interactive entertainment devices, etc.

      • Bluetooth 5.0, IEEE 802.15.4-2006, multiprotocol 2.4 GHz transceiver
      • Compatible with nRF52, nRF51, nRF24L, and nRF24AP series
      • ARM Cortex-M4F 32-bit processor (with FPU, 64MHz)
      • 1MB flash and 256kB RAM
      • 48x GPIOs
      • 2x two wire interface (I2C compatible)
      • 1x I2S digital audio interface
      • 12-bit / 200KSPS ADC
      • 1x USB2.0
      • 1x QSPI serial (32Mbps)
      • 4x SPI main interfaces, 3x SPI slave interfaces
      • 2x UART
      • 4-ch PWM
      • 1x SWD
      • Operating voltage: 1.7V~5.5V

      Core52840 Applications

      • Wearable devices
      • Bluetooth intelligent application
      • Smart home appliances
      • Industrial IoT control
      • Interactive entertainment devices

      PACKAGE CONTENT

      1. NRF52840 Eval Kit x1
      2. USB type A plug to micro B plug cable x1
      3. NFC antenna x1
      1NRF52840-Eval-Kit-1_93.jpg
      2USB-type-A-plug-to-Micro-B-plug-cable_93
      3NFC-antenna_93.jpg

      Working with Arduino / Raspberry Pi Expansions


      Attach Arduino shield

      Attach Raspberry Pi HAT

      Working with both Arduino shield and Raspberry Pi HAT

      Note: Arduino shield and Raspberry Pi HAT in the photos are not included.

      Development Resources

      Wiki : www.waveshare.com/wiki/NRF52840_Eval_Kit

      Recommendation

      You may also want an ST-LINK/V2 (mini) for easy programming / debugging.

      Waveshare Electronics
      WS-15951

      Specific References

      upc
      614961953802
      ean13
      15897
      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)

      nRF52840 Bluetooth 5.0 Evaluation Kit (WS-15951)

      €28.68

      23.90 € tax excl.