AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)
      AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)

      AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)

      AVR-USB-STK
      44,34 €

      36.95 € bez DPH

      AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)

      Množstvo:
      OUT OF STOCK

      AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)

      AVR USB AT90USB162 MICROCONTROLLER DEVELOPMENT BOARD WITH USB AND ICSP

      AT90USB162 is the easiest way to add USB functionality to your next device, Atmel provides free open source HID (mouse, keyboard) and CDC (USB-to-RS232) code and on top of this AT90USB162's cost is same as that of ATMega16, so what are you waitng for?

      The AVR-USB-STK board allows all USB features of AT90USB162 to be explored. The board has a USB connector, a Joystick, a RS232, a SD-MMC card, an Audio output, an ICSP connector and an extension connector. All AT90USB162 come from Atmel pre-programmed with bootloader which allows code to be programmed inside the chip without any external programmer, just download the FLIP software from the Atmel web site and load your HEX code inside AT90USB162. To enter the bootloader mode you should press and hold the HWB button, then press and release the RST button. If you prefer to use the ICSP programmer, note that only AVR-ISP-MK2 supports AT90USB162 as there are pretty new devices. Probably AVR Dude will add support for them later, but for the moment you can't use AVR-PG1 or AVR-PG2 for ICSP programming. Another bad news is that AT90USB162 supports only debug Wire not JTAG so to debug it you should have the expensive AT-JTAGICE-MK2.

      FEATURES

      • AT90USB162 microcontroller with 16KB Flash, 512B RAM, 512B EEPROM
      • ICSP 5x2 pin connector for in-circuit programming with AVR-ISP-MK2 (you generally don't need to use ICSP as you can program via USB)
      • Debug Wire could be performed by 3 wires connected to ICSP (AT-JTAGICE-MK2 have such lose wire connector which to be used, you need VCC, GND, RST signals only)
      • USB 2.0 Full speed connector
      • RS232 driver and connector
      • SD-MMC card connector
      • Audio out 3.5 mm jack connector
      • Extension connector with AVR port signals
      • Status LED
      • Joystick
      • User button HWB (can be used to enter bootloader mode after reset)
      • Reset button RST
      • Takes power from USB no need for external adapter
      • External power supply and voltage regulator if USB can't provide enough power
      • Quartz crystal oscillator circuit 8Mhz
      • Extension pin headers for each uC pin
      • Four mounting holes 3.3 mm (0.13")
      • Grid 100 mils
      • GND bus
      • Vcc bus
      • FR-4, 1.5 mm (0,062"), green soldermask, white silkscreen component print
      • Dimensions 100x80 mm (3.9x3.15")

      HARDWARE

      SOFTWARE

      OLIMEX
      AVR-USB-STK

      Špecifické referencie

      Stiahnuť

      AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)

      AVR-USB-STK (AT90USB162 DEV.BOARD WITH USB AND ICSP)

      44,34 €

      36.95 € bez DPH