ODROID-C4 (Hardkernel) 4GB RAM Cortex-A55 2.016GHz SoC Amlogic S905X3 Mali-G31
ODROID-C4 is a new generation single board computer that is more energy efficient and faster performing than ODROID-C2 which was introduced over four years ago as the world’s first affordable ARM 64bit computer.
The main CPU of the ODROID-C4 is built with a quad-core Cortex-A55 cluster with a new generation Mali-G31 GPU. The A55 cores run at 2.0Ghz without thermal throttling using the stock heat sink allowing a robust and quiet computer. The CPU multi-core performance is around 40% faster, and the system DRAM performance is 50% faster than the ODROID-C2.
Technical information at WiKi : https://wiki.odroid.com/odroid-c4/odroid-c4
|A||CPU (Amlogic S905X3)||H||2 x System LED indicators|
|B||DDR4 memory (4GiB)||I||1 x UART for system console|
|C||4 x USB 3.0 host ports||J||1 x IR receiver|
|D||1 x RJ45 Ethernet port (10/100/1000)||K||40 x GPIO pins|
|E||1 x HDMI 2.0||L||7 x GPIO pins|
|F||1 x Micro USB 2.0 port (OTG)||M||1 x eMMC module socket|
|G||1 x DC power jack (Outer diameter : 5.5mm, inner diameter : 2.1mm)||N||1 x Micro SD slot|
Dhrystone-2, Double-Precision Whetstone, 7-zip compression benchmark results show the ODROID-C4 system performance is 40 ~ 55% faster than the previous generation ODROID-C2. USB Host
We measured the USB3 transfer speed with a UAS capable SSD.
The average ~340MB/s of throughput should be acceptable for many applications.
Since four USB host ports share a single root hub, the transfer rate will be lower if you use multiple USB3 devices at the same time.
GPIO (40Pin Header)
The ODROID-C4 GPIO interface is similar to C2 and fully supports a 3.3Volt interface. This is beneficial for using various peripherals without complicated level shifters as with the XU4’s 1.8Volt GPIOs. Another big improvement is a faster SPI bus interface with a maximum frequency of about 100Mhz. It is significantly faster than the ODROID-C2’s 400Khz software “bit-banged” SPI.
Thanks to the modern 12nm fabricated S905X3 CPU, the power consumption and heat dissipation are relatively very low.
Therefore, we can enjoy a quiet and powerful computer with high energy efficiency.
Idle state: ≃ 0.18 Watt
Heavy load state: 3.1~3.3 Watt (stress-ng –cpu 4 –cpu-method matrixprod)
No cables are attached except DC power input and USB-UART debug console cable.
- The power consumption in “IDLE” is measured when a device is not being operated for 5 minutes since the CPU governor is set to ‘performance’.
- The measured power consumption is not absolute and could vary in certain conditions.
|Form factor||Board Dimensions: 85mm x 56mm x 1.0mm
Heatsink Dimensions: 40mm x 32mm x 10mm
Weight: 59g including heatsink
|Processor||Amlogic S905X3 12nm Processor
L1 instruction cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L1 data cache: 32 KB, 4-way set associative (128 sets), 64 byte lines, shared by 1 processor
L3 data cache: 512KB , 16-way set associative (512 sets), 64 byte lines, shared by 4 processors
Quad-Core Cortex-A55 (2.016GHz)
ARMv8-A architecture with Neon and Crypto extensions
Mali-G31 MP2 GPU with 4 x Execution Engines (650Mhz)
|Memory||DDR4 4GiB with 32-bit bus width
Data rate: 2640 MT/s (PC4-21333 grade)
1.2Volt low power design
|Storage||1x eMMC connector (8/16/32/64GiB are available)
1x Micro SD slot (DS/HS mode up to UHS-I SDR104)
|Networking||1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)
– Realtek RTL8211F (Ethernet transceiver)
– LED indicators
* Green LED: Flashing by data traffic at 100Mbps connection
* Amber LED: Flashing by data traffic at 1000Mbps connection
Optional WiFi USB adapters
|Video||1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)|
|Audio||1 x HDMI digital output
1 x Optional SPDIF optical output
|External I/O||4 x USB 3.0 Host ports (shares one single root hub)
1 x USB 2.0 OTG port for Host or Device mode. (No power input)
1 x Debug serial console (UART)
1 x Peripheral Expansion Header (40-pin, 2.54mm pitch)
1x Audio Expansion Header (7-pin, 2.54mm pitch)
– All 3.3V I/O signal level except for ADC input at max 1.8Volt.
|Other features||IR receiver for remote controller
System LEDS Indicators:
– Red (PWR) – Solid light when DC power is connected
– Blue (ALIVE) – Flashing like heartbeat while Kernel is running.
|Power||1 x DC jack : outer (negative) diameter 5.5mm, inner (positive) diameter 2.1mm
DC input : 5.5V ~ 15.5V
– DC 12V/2A power adaptor is recommended
– IDLE : ≃ 1.8W
– CPU Stress : ≃ 3.64W (Performance governor)
– Power-off : ≃ 0.14W
You might also like
Customers who bought this product also bought:
16 other products in the same category:
34.90 € tax excluded
29.00 € tax excluded