ScanaPLUS  (IKALOGIC)  100MHz 9-Channels logic analyzer 1.2/1.8/3.3/5/12/±12V

• Manual
• Decoders
• Community
• Download Scanastudio

ScanaPLUS is a Logic Analyzer. It allows you to “capture” the state of logic signals for a certain amount of time, and then display them on a screen. It’s like an oscilloscope, but optimized for Logic Signals.

ScanaPLUS is the only 9-channel logic analyzer out there. Just enough to look at an 8-bit bus and a sync/clock signal on the 9th channel!

It also have a shiny blue led that blinks when activity is detected on any channel. That’s a time saver when a quick sanity check is needed!

Serial protocols

Working with an I2C humidity sensor? A 1-Wire temperature sensor? An SPI Flash memory? Or sending data over Serial port?

If that’s the case, you need a Logic Analyzer. Trust us, it will change your life.

ScanaPLUS is designed to help you visualize and debug your serial interface. ScanaStudio software will decode and interpret data for you. It will even pinpoint you directly to any wrong or suspicious signals! The image below shows a decoded I2C communication between a micro controller and a humidity sensor. 

Maximum sampling rate	100 MHz
Timing accuracy	± 10 ns (In all modes)
Channels	9
Differential inputs	4 (Channel 5 to 8 form 2 differential pairs)
Input bandwidth (Max.)	25 MHz (1 channel) | 16MHz (4 channels) | 10 MHz (All 9 channels)
Supported logic levels	1.2V | 1.8V | 3.3V | 5V | 12V | ±12V (RS232) | Differential (CAN/RS485)
Trigger options	Rising edge | Falling edge | Logic level | Pulse width | Serial sequence
Input voltage range	± 24V (continuous) | ±50V (10s pulse width)
Input impedance	100KΩ
Input capacitance	10pF Maximum
Weight & Dimensions:	Weight: 59 gm (2.08 oz) | 73 x 46 x 17 mm (2.87 x 1.81 x 0.67 inches)
In the box	Logic analyzer pod | 10 wires harness | 10 precision grabber test clips | USB cable

ScanaPLUS Logic Analyzer has a versatile input stage; 9 channel inputs can be configured in many ways. Among those, 2 channels may be configured as differential pairs (instead of the standard single-ended line).

This allows direct connection to industrial and automobile data buses like RS485 and CAN bus.

Screenshot below shows a CAN bus data frame being analyzed with ScanaStudio: 

Similar input configurations are possible for other industrial buses like LIN and RS232.

Sometime you just need to do the most basic thing that can be done with a measurement device: Measure!

With ScanaPLUS & ScanaStudio, you can measure time, frequency and duty cycle in a very user friendly way!

In the example below, a clock signal’s frequency is measured. The deviation of that frequency around a mean value is also displayed 

ScanaPLUS is also a great tool when it comes to reverse engineer a digital circuit.

ScanaPLUS allows you to capture logic signals of various types (1.8V, 3.3V, 5V) for very long duration (up to 2000 seconds).

ScanaStudio provides an IDE to write your own decoder to help you make sense out of captured data.

ScanaPLUS V2 is a robust, versatile and multi-application 9 Channels logic analyzer. It relies on the free ScanaStudio software to capture and analyze logic signals.

Basic information

• Number of adjustable logic threshold groups: 2
• Adjustable logic levels for each group: 1.2V, 1.5V, 1.8V, 2.8V, 3.3V to 5V
• Number of integrated receivers for RS232 bus: 5
• Number of integrated receivers for LIN bus: 5
• Number of integrated differential lines receivers: 2 (can used for CAN, RS485, etc.)
• Activity LED integrated to ScanaPLUS device quickly indicates logic change on any line
• Input operating range ± 35V
• Absolute maximum input range ± 50V
• Input impedance 100KΩ || 5pF

Sophisticated Trigger options

• Configurable trigger event types: Rising edge, Falling edge, Logic level, Pulse width
• Multi-channel trigger support: Yes
• Number of cascaded events to trigger: Unlimited number of events

Software characteristics summary