Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)
      Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)

      Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)

      AF-3179
      €47.88

      39.90 € tax excl.

      Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)

      Quantity :
      OUT OF STOCK

      Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)

      • Feather is the new development board from Adafruit, and like its namesake it is thin, light, and lets you fly! We designed Feather to be a new standard for portable microcontroller cores.

        This is the Adafruit Feather M0 RFM96 LoRa Radio (433 MHz) - our take on an microcontroller with a "Long Range (LoRa)" packet radio transceiver with built in USB and battery charging. Its an Adafruit Feather M0 with a 433MHz radio module cooked in! Great for making wireless networks that are more flexible than Bluetooth LE and without the high power requirements of WiFi. We have other boards in the Feather family, check'em out here.

        This is the 433 MHz radio version. We also sell a 898/915 MHz version of the same radio chipset!

        At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic, the same one used in the newArduino Zero. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip.

        To make it easy to use for portable projects, we added a connector for any of our 3.7V Lithium polymer batteries and built in battery charging. You don't need a battery, it will run just fine straight from the micro USB connector. But, if you do have a battery, you can take it on the go, then plug in the USB to recharge. The Feather will automatically switch over to USB power when its available. We also tied the battery thru a divider to an analog pin, so you can measure and monitor the battery voltage to detect when you need a recharge.

        Here's some handy specs! Like all Feather M0's you get:

        • Measures 2.0" x 0.9" x 0.3" (51mm x 23mm x 8mm) without headers soldered in
        • Light as a (large?) feather - 5.8 grams
        • ATSAMD21G18 @ 48MHz with 3.3V logic/power
        • No EEPROM
        • 3.3V regulator with 500mA peak current output
        • USB native support, comes with USB bootloader and serial port debugging
        • You also get tons of pins - 20 GPIO pins
        • Hardware Serial, hardware I2C, hardware SPI support
        • 8 x PWM pins
        • 10 x analog inputs
        • 1 x analog output
        • Built in 100mA lipoly charger with charging status indicator LED
        • Pin #13 red LED for general purpose blinking
        • Power/enable pin
        • 4 mounting holes
        • Reset button

        This Feather M0 LoRa Radio uses the extra space left over to add an RFM9x LoRa 868/915 MHz radio module. These radios are not good for transmitting audio or video, but they do work quite well for small data packet transmission when you need more range than 2.4 GHz (BT, BLE, WiFi, ZigBee).

        • SX127x LoRa® based module with SPI interface
        • Packet radio with ready-to-go Arduino libraries
        • Uses the license-free ISM bands (ITU "Europe" @ 433MHz and ITU "Americas" @ 900MHz)
        • +5 to +20 dBm up to 100 mW Power Output Capability (power output selectable in software)
        • ~300uA during full sleep, ~120mA peak during +20dBm transmit, ~40mA during active radio listening.
        • Simple wire antenna or spot for uFL connector

        Our initial tests with default library settings: over 1.2mi/2Km line-of-sight with wire quarter-wave antennas. (With setting tweaking and directional antennas, 20Km is possible).

        Comes fully assembled and tested, with a USB bootloader that lets you quickly use it with the Arduino IDE. We also toss in some headers so you can solder it in and plug into a solderless breadboard. You will need to cut and solder on a small piece of wire (any solid or stranded core is fine) in order to create your antenna. Lipoly battery and USB cable not included but we do have lots of options in the shop if you'd like!

      Adafruit Industries
      AF-3179

      Specific References

      Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)

      Adafruit Feather M0 RFM96 LoRa Radio - 433MHz (Adafruit 3179)

      €47.88

      39.90 € tax excl.