By continuing use this site, you agree to the Terms & Conditions and our use of cookies.

      ODROID-N2+ with 4GByte RAM (G200702239825) Hardkernel N2plus

      HK-ODROID-N2PLUS-4GB
      €119.94
      Tax included

      99.95 € tax excl.

      ODROID-N2+ with 4GByte RAM (G200702239825) Hardkernel N2plus

      Quantity :
      • Secure purchase
      • Fast delivery
      • Purchase help

      ODROID-N2+ with 4GByte RAM (G200702239825) Hardkernel N2plus

      ODROID-N2+ is a revision from ODROID-N2.

      • – Maximum CPU clock of Quad-core Cortex-A73 is increased to 2.4Ghz from 1.8Ghz.
      • – Maximum CPU clock of Dual-core Cortex-A53 is increased to 2.0Ghz from 1.9Ghz.
      • – On-board RTC backup battery holder is mounted on the board.

      The main CPU is based on big.Little architecture which integrates a quad-core ARM Cortex-A73 CPU cluster and a dual core Cortex-A53 cluster with a new generation Mali-G52 GPU.
      Thanks to the modern 12nm silicon technology, the A73 cores run at 2.2Ghz without thermal throttling using the stock metal-housing heatsink allowing a robust and quiet computer.
      The CPU multi-core performance is around 20% faster and the GPU is 10% faster than the N1. The N2+’s DDR4 RAM is running at 1320Mhz with 1.2volt low power consumption.
      The large metal housing heatsink is designed to optimize the CPU and RAM heat dissipation and minimize throttling. The CPU is placed on the bottom side of the PCB to establish great thermal characteristics.

      More information is on our WiKi.

      Board Detail

      A S922X CPU J 1 x SPI Flash 8MiB
      B 4 x DDR4 RAM K 1 x SPI Boot Select Switch
      C 1 x RJ45 Ethernet Port (10/100/1000) L 1 x eMMC Module Socket
      D 1 x HDMI 2.0 M 1 x Micro SD Slot
      E 4 x USB 3.0 N 1 x IR Receiver
      F 2 x System LED Indicators O 1 x RTC Backup Battery Holder
      G 1 x DC Power Jack P 1 x Active Cooling Fan Connector (2-pin)
      H 1 x AV Out (Stereo Audio with Composite video) Q 40 x GPIO Pins
      I 1 x Micro USB2.0 OTG R 1 x UART for System Console

      Optional Active Cooler

        

      Heatsink size comparison : The system height decreased from 34mm to 29mm approximately thanks to the slimmer heatsink.







      GPIO (40Pin header)
      figure-17.png

      The N2 GPIO interface is similar to C2 and fully supports a 3.3Volt interface while N1 could only support 2.8Volt IO. This is beneficial for using various peripherals without complicated level shifters.
      Another big improvement is a faster SPI bus interface. Its maximum frequency is over 150Mhz, and we will try to implement a DMA driven SPI driver for faster LCD display.

      Power consumption
      Idle state: 1.6~1.8 Watt
      Heavy load state: 5.9~6.2 Watt (stress-ng –cpu 6 –cpu-method matrixprod)
      No cables are attached except DC power input and USB-UART debug console cable.

       

      Software support

      Linux
      Ubuntu 20.04 LTS images are available with Kernel version 4.9.230 LTS as of today. This LTS kernel version will be officially supported until Jan, 2023.
      The Mali G52 GPU Linux driver works only on the framebuffer and Wayland. We tested the latest PPSSPP emulation and it can handle x3 scaling on a 4K display nicely with well implemented VSYNC.
      The fb-dev Mali driver supports OpenGL-ES 1.1, 2.0, 3.0 and 3.1 as well as OpenCL-1.2 and 2.0 at this moment. Note that you have to use the Minimal Ubuntu OS image to utilize the GPU acceleration instead of the Ubuntu Mate image.

      There is a Linux Wayland driver too. Ubuntu 20.04 Gnome desktop works with fully accelerated hardware GPU on a modern Kernel 5.7.
      This trial upstream OS image is available on the forum.

      Android
      Android 9 Pie is ready, and you can access a source code BSP and pre-built image together. Note that GUI layer(SurfaceFlinger) resolution is limited at 2K while the video layer is true 4K.
      The Android platform is based on a full 64bit system software with a Vulkan capable GPU driver.

       

      SBC Specification

      Form Factor Board Dimensions: 90mm x 90mm x 17mm

      Heatsink Dimensions: 100mm x 91mm x 18.75mm

      Weight: 200g including heatsink

      Processor Amlogic S922X Processor (12nm fab)

      Quad-core Cortex-A73(up to 2.4Ghz) and Dual-core Cortex-A53 (up to 2Ghz)

      ARMv8-A architecture with Neon and Crypto extensions

      Mali-G52 GPU with 6 x Execution Engines (800Mhz)

      Memory DDR4 4GiB or 2GiB with 32-bit bus width

      Data rate: 2640 MT/s (PC4-21333 grade)

      1.2Volt low power design

      Storage 1 x eMMC connector (8G, 16G, 32G and 64G are available)

      1 x microSD slot (DS/HS modes up to UHS-I SDR104)

      Networking 1 x GbE LAN ports (RJ45, supports 10/100/1000 Mbps)

      – Realtek RTL8211F (Ethernet transceiver)

      – LED indicators

      * Green LED: Flashing by data traffics at 100Mbps connection

      * Amber LED: Flashing by data traffics at 1000Mbps connection

      Optional WiFi USB adapters

      Video 1 x HDMI 2.0 (up to 4K@60Hz with HDR, CEC, EDID)

      1 x Composite video (3.5mm jack)

      Audio 1 x Stereo Audio line-out (3.5mm jack)

      1 x HDMI digital output

      1 x Optional SPDIF optical output

      External I/O 4 x USB 3.0 Host ports (shares one single root hub)

      1 x USB 2.0 OTG port for Host or Device mode. (No power input)

      1 x Debug serial console (UART)

      1 x Peripheral Expansion Header (40-pin, 2.54mm pitch)

      – 2 x DC 5V, 2 x DC 3.3V, 1 x DC 1.8V, 8 x GND

      – 1 x SPI

      – 1 x UART

      – 2 x I2C

      – 25 x GPIO (Max)

      – 2 x ADC input (10bit, 1.8V Max)

      – All 3.3V I/O signal level except for ADC input at max 1.8Volt.

      Other features On board RTC(Real Time Clock) IC to keep date and time. A CR2032 coin battery holder was replaced with the 2-pin 1.25mm pitch connector.

      No battery is included in the board.

      Please purchase the very common bare CR2032 cell from your local store.

      You can keep the RTC time up to several years with a 200mAh CR2032 battery.

      8MiB SPI Flash for boot manager

      IR receiver for remote controller

      Built with a large passive heatsink

      System LEDS Indicators:

      – Red (PWR) – Solid light when DC power is connected

      – Blue (ALIVE) – Flashing like heartbeat while Kernel is running.

      Active Cooling Fan Connector (5V 2-pin)

      – Connector (2-pin, 1.25mm pitch)

      Power 1 x DC jack : outer (negative) diameter 5.5mm, inner(positive) diameter 2.1mm

      DC 7.5V ~ 18V (up to 25W)

      – DC 12V/2A power adaptor is recommended

      Power consumption:

      – IDLE : ≃ 2.2W (Performance governor)

      – CPU Stress : ≃ 5.9W (@2016/2208MHz), 6.2W (@2016/2400MHz)

      – Power-off : ≃ 0.2W

      Hardkernel
      HK-ODROID-N2PLUS-4GB

      Specific References

      You might also like

      Customers who bought this product also bought:

      16 other products in the same category: