• New
    EVK407I, STM32F4 Development Board (WS-15238)
    EVK407I, STM32F4 Development Board (WS-15238)
    EVK407I, STM32F4 Development Board (WS-15238)
    EVK407I, STM32F4 Development Board (WS-15238)
    EVK407I, STM32F4 Development Board (WS-15238)

    EVK407I, STM32F4 Development Board (WS-15238)

    WS-15238
    €162.00

    135.00 € tax excl.

    EVK407I, STM32F4 Development Board (WS-15238)

    Quantity :
    OUT OF STOCK

    EVK407I, STM32F4 Development Board (WS-15238)

    STM32 Development Board, STM32F407IGT6, USB HS/FS, Ethernet, NandFlash, JTAG/SWD, LCD, USB TO UART

    Overview

    EVK407I is an STM32 development board which consists of a mother board and a MCU core board XCore407I.


    What's on the mother board

    STM32F407IGT6 development board on board resource

    1. MCU core board connector
    2. MCU pins expander
    3. JTAG/SWD interface, for debugging/programming
    4. LCD interface, for connecting touch screen LCD
    5. USB connector, USB TO UART
    6. 5V DC jack
    7. PL2303TA, onboard USB TO UART controller
    8. PL2303 jumper
    9. User LED jumper
    10. Joystick jumper
    11. 12M crystal, PL2303 clock
    12. User LEDs, convenient for indicating I/O status and/or program running state
    13. UART LEDs, UART TX/RX indicator
    14. Joystick

    For jumpers 8-10:

    • short the jumper to connect to I/Os used in example code
    • open the jumper to connect to other custom pins via jumper wires

    What's on the MCU core board

    STM32F407IGT6 development board on board resource

    1. STM32F407IGT6:the high performance STM32 MCU which features:
      • Core: Cortex-M4 32-bit RISC
      • Feature: a full set of single-cycle DSP instructions
      • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
      • Operating Voltage: 1.8V-3.6V
      • Package: LQFP176
      • Memories: 1024kB Flash, 192+4kB SRAM
      • MCU communication Interfaces:
        • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
        • 1 x FSMC, 1 x SDIO, 2 x CAN
        • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
        • 1 x 10/100 Ethernet MAC
        • 1 x 8 to 14-bit parallel camera interface
      • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
      • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
    2. MIC2075-2, onboard USB FS power management device
    3. AMS1117-3.3, 3.3V voltage regulator
    4. K9F1G08U0E, 1G Bit NandFlash
    5. DP83848, Ethernet PHY
    6. MIC2075-1, onboard USB HS power management device
    7. USB3300, USB HS PHY
    8. Power supply switch, powered from 5Vin or USB connection
    9. Boot mode switch, for configuring BOOT0 pin
    10. Power indicator
    11. USB FS LED
    12. USB HS LED
    13. Reset button
    14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication
    15. 24M crystal, USB3300 clock
    16. 50M crystal, DP83848 clock
    17. 32.768K crystal, for internal RTC with calibration
    18. Ethernet connector
    19. USB FS mini connector
    20. USB HS mini connector
    21. USB HS type A connector
    22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion
    23. USB OTG/HOST jumper
    24. VREF/VBAT jumper
    25. Ethernet I/O selection solder joint
    26. USB HS I/O selection solder joint
    27. PDR selection solder joint: 1.8-3.6V, -40~105℃ OR 1.7-3.6V, 0~70℃

    Photos

    STM32 Development Board
    EVK407I development board
    STM32 Development Board
    EVK407I development board
    STM32 Development Board
    EVK407I development board back view
    STM32 Development Board
    EVK407I mother board
    STM32 MCU Core Board
    MCU core board XCore407I
    STM32 MCU Core Board
    MCU core board XCore407I
    STM32 Development Board
    EVK407I connectivity
     

    EVK407I μC/OS-II (Ⅰ)

    EVK407I μC/OS-II (Ⅱ)

    EVK407I μC/OS-II (Ⅲ)

    EVK407I μC/OS-II (Ⅳ)

    JTAG/SWD interfaces

    The figure 1, and 2 show the header pinouts of JTAG/SWD interface

    Figure 1. JTAG Header Pinout
    JTAG Header Pinout
    Figure 2. SWD Header Pinout
    SWD Header Pinout

    Development Resources

    • Related software (KEIL etc.)
    • Examples in C
    • Schematic (PDF)
    • Development documentations

    Wiki: www.waveshare.com/wiki/EVK407I

    Balenie Obsahuje / Package Content

    1. EVK407I development board x 1
    2. 3.2inch 320x240 Touch LCD x 1
    3. USB type A plug to mini-B plug cable x 1
    4. USB type A receptacle to mini-B plug cable x 1
    5. 4-pin wire x 2
    6. 2-pin wire x 2
    7. USB power cable x 1
    8. Software CD x 1
    Waveshare Electronics
    WS-15238

    Specific References

    EVK407I, STM32F4 Development Board (WS-15238)

    €162.00

    135.00 € tax excl.