RLX COMPONENTS s.r.o. , Electronic Components Distributor.
RLX COMPONENTS s.r.o. , Electronic Components Distributor.
mDrawbot Kit - Standard (Makeblock 90070)
MB-90070
mDrawbot Kit - Standard (Makeblock 90070)
mDrawbot Kit - Standard (Makeblock 90070)
mDrawBot is the world's most fully-featured four-in-one drawing robot. It can be assembled into 4 different configurations: mScara, mSpider, mEggBot, and mCar.
This kit consists of over 60 components from Makeblock, including beams, brackets, motor, etc. It also comes with a specially-designed software named mDraw to control these robots. Here's the picture of all the components.
Specifications
1. Frame: Anodized Aluminum
|
|
mScara |
mSpider |
mEggBot |
mCar |
|
Working Area (mm2) |
120° of an annulus (exradius 208mm, inradius 168mm) |
/ |
Cylinder with L×D=60×10-60 |
/ |
2. Power Supply:
|
|
Voltage |
Current |
Frequency |
|
Input |
AC 100-240 V |
0.6A |
50-60 Hz |
|
Output |
DC 12 V |
2.0 A |
/ |
3. Main Controller: Makeblock Orion (Arduino UNO compatible)
4. Software: mDraw
5. Connection: USB or Bluetooth
6. Supported File Types: .Plain SVG, .BMP etc.
7. Supported OS: Windows7 or later. (Will be available in Mac OS X, Linux soon.)
8. Package Contains:
- Aluminum Extrusion Parts
- Plastic Timing Pulley 90T
- Timing Pulley 18T
- Pen Lift Mechanism
- Makeblock Orion(Controller)
- Stepper Motors
- Stepper Motor Drivers
- 9g Micro Servo Pack
- Cables
- Other Hardware and Accessories
mScara
mScara is a SCARA (Selective Compliance Articulated Robot Arm) driven by stepper motors. Adding a pen on mScara, it can draw pictures on a flat surface. You can also turn mScara into a desktop laser engraver replacing the pen with a laser diode.
mSpider
mSpider is a drawing robot which can draw pictures on a wall or a white board. Two stepper motors control the movement of mSpider though strings. Theoretically, its drawing range can be expanded by increasing the length of the strings.
mEggBot
mEggBot is designed to draw on things that are improbable to print on, such as eggs or ping-pong balls. It can be used to write letters, draw expressions on spheroid, or draw Easter eggs.
mCar
mCar is a three-wheel robot car, which contains two stepper-motor-drive wheels and a ball-caster wheel. It can draw its own movement tracks on flat surface. Installing a chalk instead of a pen, it can draw on the floor.
How to Use mDrawBot?
Assembly
Each mDrawBot kit can be assembled into any of the 4 different configurations. We provide the detailed assembling instructions that enables you to build any configuration in an hour.
The assembly instructions and the user guide can be downloaded here:
http://learn.makeblock.cc/mdrawbot/
mDrawBot Animation Assembly
mScara
mSpider
mEggBot
mCar
Software
mDraw is the software specially designed for mDrawBot. After installing the mDraw software, you can import images that you wish your robot to draw. It is completely compatible with the four forms of mDrawBot and also both the servo mode and laser mode of Makeblock XY Plotter V2.0.
Features of mDraw
- Support mScara, mSpider, mEggBot, mCar, XY
- Support both pen drawing and laser engraving
- Support custom settings of motor direction, drawing range, etc
- Support saving parameters
- Support SVG. file
- Support conversion from BMP to SVG
- Support zooming, rotating, mirroring, and moving the SVG graphics
- Support Windows7 or later. (Will be available in Mac OS X, Linux soon.)
mDraw is an open source project hosted on Github. Fork it here:https://github.com/Makeblock-official/mDrawBot.
A Drawbot, and More than A Drawbot
mDrawBot is a drawbot (or 4 drawbots), and it's more than a drawbot. You can re-use the Makeblock robot parts in countless new projects and it's easy to extend the kit with new parts. Here are some examples of what you can do:
mScara(Standard Version)
mScara(Laser Version)
mSpider
mEggBot
mCar
About laser engraver pack (500mW)
WARNING: As laser energy has higher density, make sure corresponding protection measures are taken while using.
- No direct eye-contact with the laser light path;
- DO NOT irradiate others by the laser;
- Keep it away from children and other people who are not familiar with laser usage;
Specifications
|
laser engraver pack (500mW) |
Remark |
|
|
Wavelength |
405nm |
|
|
Power |
500mW |
|
|
W/ Voltage Conversion Box |
Input DC 12V 1.5A |
+ |
|
W/O Voltage Conversion Box |
Input DC 5V±0.2V 200mA |
- |
|
Operating Temperature |
0℃-50℃ |
|
|
Storage & Transport temperature |
-40℃-85℃ |
|
Processable Material
|
Material |
Cut |
Engraver |
|
Paper |
YES |
YES |
|
Cardboard |
up to 1.5mm |
YES |
|
Wood Board |
up to 1.5mm |
YES |
|
Rubber Sheet |
up to 0.5mm |
YES |
|
Foam Paper |
up to 2.5mm |
YES |
|
Dark color cloth (jean cloth, cotton cloth and linen) |
up to 0.5mm |
YES |
|
Non-transparent ACRYL |
Up to 0.5mm (※ 1) |
YES |
|
Plastic Sheet |
Up to 0.25mm (※ 2) |
YES |
|
Urethane Sheet |
up to 2mm up |
YES |
|
Mirror |
NO |
NO |
|
Glass |
NO |
NO |
|
Ceramic |
NO |
NO |
|
Aluminum |
NO |
YES (※ 3) |
|
Steel |
NO |
NO |
|
Stainless |
NO |
NO |
※1. Opaque black acrylic only, ※ 2.Gray plastic plate only, ※ 3.Peeling of anodized only
About mDrawBot’s upgrade.
You can also design your own upgrade pack for your mDrawBot. By adding an accelerometer and gyro sensor, it will become a two-wheeled self-balancing vehicle. Add some additional Makeblock mechanical parts and it may be transformed into a XY plotter. The only limit is your imagination.
Part List
(Standard Version ) SKU: 90070
|
1 x Beam 0824-032 |
1 x Threaded Shaft 4x39mm |
50 x Nut M4 |
|
2 x Beam 0824-096 |
1 x Circle Shaft D4x80mm |
4 x Nylon Stud M4x30 |
|
3 x Beam 0324-184 |
2 x Shaft Collar 4mm |
2 x Plastic Ring 4x8x1mm |
|
3 x Bracket 3x3 |
5 x Flange Bearing 4x8x3mm |
8 x Plastic Ring 4x7x3mm |
|
3 x Plate 3x6 |
1 x Square Nut M4 |
4 x Plastic Ring 4x7x10mm |
|
1 x Bracket U1 |
3 x Nylon Cap Nut M4 |
2 x Plastic Rivet R4060 |
|
4 x Timing Pulley Slice 90T |
1 x Polyester Thread(8m) |
4 x Plastic Rivet R40120 |
|
2 x 42BYG Stepper Motor Bracket |
2 x Timing Belt 112MXL |
1 x 9g Micro Servo Pack |
|
2 x Plastic Timing Pulley 90T |
10 x Nylon Cable Tie 2 x100 |
2 x 42BYG Stepper Motor |
|
2 x Tire 90T B |
1 x Rubber Bank |
2 x Base Bracket |
|
1 x Caster Wheel |
1 x Cross&2.5mm HEX Screwdriver |
1 x Battery Holder |
|
2 x Rubber Blanket |
1 x HEX Key 1.5mm |
1 x Makeblock Orion |
|
2 x Shaft Connector 4mm |
1 x Wrench 5mm&7mm |
2 x Me Stepper Motor Driver |
|
2 x Timing Pulley 18T |
26 x Screw M4x8 |
1 x RJ25 Adapter |
|
1 x Pen Holder and V Clamp |
42 x Screw M4x16 |
1 x AC/DC Adapter 12V/2A |
|
2 x 2 Inch G Clamp |
5 x Screw M4x22 |
1 x 9g Servo Extension Cord |
|
1x Plastic Hinge |
1 x Screw M4x35 |
2 x 6P6C RJ25 Cable-20cm |
|
1 x Plastic Hinge Gasket |
6 x Headless Set Screw M3x5 |
1 x 6P6C RJ25 Cable-35cm |
|
1 x Spring 0.6x6x50 |
8 x Countersunk Screw M3x8 |
1 x Micro USB Cable |
|
1×tape 100cmPaper |
|
|
(Bluetooth Version ) SKU: 90078
|
1 x Beam 0824-032 |
1 x Threaded Shaft 4x39mm |
50 x Nut M4 |
|
2 x Beam 0824-096 |
1 x Circle Shaft D4x80mm |
4 x Nylon Stud M4x30 |
|
3 x Beam 0324-184 |
2 x Shaft Collar 4mm |
2 x Plastic Ring 4x8x1mm |
|
3 x Bracket 3x3 |
5 x Flange Bearing 4x8x3mm |
8 x Plastic Ring 4x7x3mm |
|
3 x Plate 3x6 |
1 x Square Nut M4 |
4 x Plastic Ring 4x7x10mm |
|
1 x Bracket U1 |
3 x Nylon Cap Nut M4 |
2 x Plastic Rivet R4060 |
|
4 x Timing Pulley Slice 90T |
1 x Polyester Thread(8m) |
4 x Plastic Rivet R40120 |
|
2 x 42BYG Stepper Motor Bracket |
2 x Timing Belt 112MXL |
1 x 9g Micro Servo Pack |
|
2 x Plastic Timing Pulley 90T |
10 x Nylon Cable Tie 2 x100 |
2 x 42BYG Stepper Motor |
|
2 x Tire 90T B |
1 x Rubber Bank |
2 x Base Bracket |
|
1 x Caster Wheel |
1 x Cross&2.5mm HEX Screwdriver |
1 x Battery Holder |
|
2 x Rubber Blanket |
1 x HEX Key 1.5mm |
1 x Makeblock Orion |
|
2 x Shaft Connector 4mm |
1 x Wrench 5mm&7mm |
2 x Me Stepper Motor Driver |
|
2 x Timing Pulley 18T |
26 x Screw M4x8 |
1 x RJ25 Adapter |
|
1 x Pen Holder and V Clamp |
42 x Screw M4x16 |
1 x AC/DC Adapter 12V/2A |
|
2 x 2 Inch G Clamp |
5 x Screw M4x22 |
1 x 9g Servo Extension Cord |
|
1 x Plastic Hinge |
1 x Screw M4x35 |
2 x 6P6C RJ25 Cable-20cm |
|
1 x Plastic Hinge Gasket |
6 x Headless Set Screw M3x5 |
1 x 6P6C RJ25 Cable-35cm |
|
1 x Spring 0.6x6x50 |
8 x Countersunk Screw M3x8 |
1 x Micro USB Cable |
|
1 x Me-Bluetooth 4.0 |
1×tape 100cmPaper |
|
(Laser Version ) SKU: 90082
|
1 x Beam 0824-032 |
1 x Threaded Shaft 4x39mm |
50 x Nut M4 |
|
2 x Beam 0824-096 |
1 x Circle Shaft D4x80mm |
4 x Nylon Stud M4x30 |
|
3 x Beam 0324-184 |
2 x Shaft Collar 4mm |
2 x Plastic Ring 4x8x1mm |
|
3 x Bracket 3x3 |
5 x Flange Bearing 4x8x3mm |
8 x Plastic Ring 4x7x3mm |
|
3 x Plate 3x6 |
1 x Square Nut M4 |
4 x Plastic Ring 4x7x10mm |
|
1 x Bracket U1 |
3 x Nylon Cap Nut M4 |
2 x Plastic Rivet R4060 |
|
4 x Timing Pulley Slice 90T |
1 x Polyester Thread(8m) |
4 x Plastic Rivet R40120 |
|
2 x 42BYG Stepper Motor Bracket |
2 x Timing Belt 112MXL |
1 x 9g Micro Servo Pack |
|
2 x Plastic Timing Pulley 90T |
10 x Nylon Cable Tie 2 x100 |
2 x 42BYG Stepper Motor |
|
2 x Tire 90T B |
1 x Rubber Bank |
2 x Base Bracket |
|
1 x Caster Wheel |
1 x Cross&2.5mm HEX Screwdriver |
1 x Battery Holder |
|
2 x Rubber Blanket |
1 x HEX Key 1.5mm |
1 x Makeblock Orion |
|
2 x Shaft Connector 4mm |
1 x Wrench 5mm&7mm |
2 x Me Stepper Motor Driver |
|
2 x Timing Pulley 18T |
26 x Screw M4x8 |
1 x RJ25 Adapter |
|
1 x Pen Holder and V Clamp |
42 x Screw M4x16 |
1 x AC/DC Adapter 12V/2A |
|
2 x 2 Inch G Clamp |
5 x Screw M4x22 |
1 x 9g Servo Extension Cord |
|
1 x Plastic Hinge |
1 x Screw M4x35 |
2 x 6P6C RJ25 Cable-20cm |
|
1 x Plastic Hinge Gasket |
6 x Headless Set Screw M3x5 |
1 x 6P6C RJ25 Cable-35cm |
|
1 x Spring 0.6x6x50 |
8 x Countersunk Screw M3x8 |
1 x Micro USB Cable |
|
1 x Laser Engraver Upgrade Pack(500mW) |
1×tape 100cmPaper |
|
(Laser+Bluetooth Version ) SKU: 90086
|
1 x Beam 0824-032 |
1 x Threaded Shaft 4x39mm |
50 x Nut M4 |
|
2 x Beam 0824-096 |
1 x Circle Shaft D4x80mm |
4 x Nylon Stud M4x30 |
|
3 x Beam 0324-184 |
2 x Shaft Collar 4mm |
2 x Plastic Ring 4x8x1mm |
|
3 x Bracket 3x3 |
5 x Flange Bearing 4x8x3mm |
8 x Plastic Ring 4x7x3mm |
|
3 x Plate 3x6 |
1 x Square Nut M4 |
4 x Plastic Ring 4x7x10mm |
|
1 x Bracket U1 |
3 x Nylon Cap Nut M4 |
2 x Plastic Rivet R4060 |
|
4 x Timing Pulley Slice 90T |
1 x Polyester Thread(8m) |
4 x Plastic Rivet R40120 |
|
2 x 42BYG Stepper Motor Bracket |
2 x Timing Belt 112MXL |
1 x 9g Micro Servo Pack |
|
2 x Plastic Timing Pulley 90T |
10 x Nylon Cable Tie 2 x100 |
2 x 42BYG Stepper Motor |
|
2 x Tire 90T B |
1 x Rubber Bank |
2 x Base Bracket |
|
1 x Caster Wheel |
1 x Cross&2.5mm HEX Screwdriver |
1 x Battery Holder |
|
2 x Rubber Blanket |
1 x HEX Key 1.5mm |
1 x Makeblock Orion |
|
2 x Shaft Connector 4mm |
1 x Wrench 5mm&7mm |
2 x Me Stepper Motor Driver |
|
2 x Timing Pulley 18T |
26 x Screw M4x8 |
1 x RJ25 Adapter |
|
1 x Pen Holder and V Clamp |
42 x Screw M4x16 |
1 x AC/DC Adapter 12V/2A |
|
2 x 2 Inch G Clamp |
5 x Screw M4x22 |
1 x 9g Servo Extension Cord |
|
1 x Plastic Hinge |
1 x Screw M4x35 |
2 x 6P6C RJ25 Cable-20cm |
|
1 x Plastic Hinge Gasket |
6 x Headless Set Screw M3x5 |
1 x 6P6C RJ25 Cable-35cm |
|
1 x Spring 0.6x6x50 |
8 x Countersunk Screw M3x8 |
1 x Micro USB Cable |
|
1 x Laser Engraver Upgrade Pack(500mW) |
1 x Me-Bluetooth 4.0 |
1×tape 100cmPaper
|
MB-90070
Specific References
mDrawbot Kit - Standard (Makeblock 90070)