By continuing use this site, you agree to the Terms & Conditions and our use of cookies.
      XCore407I, STM32F4 Core Board (WS-7696)
      • XCore407I, STM32F4 Core Board (WS-7696)

      XCore407I, STM32F4 Core Board (WS-7696)

      WS-7696
      €114.00
      Tax included

      95.00 € tax excl.

      XCore407I, STM32F4 Core Board (WS-7696)

      Quantity :
      • Secure purchase
      • Fast delivery
      • Purchase help

      XCore407I, STM32F4 Core Board (WS-7696)

      STM32 MCU core board, STM32F407IGT6, IO expander, USB HS/FS, Ethernet, NandFlash

      Overview

      XCore407I is an STM32 MCU core board that features the STM32F407IGT6 on board.

      • Clock circuit, USB power management
      • Onboard devices: USB HS PHY、Ethernet PHY、1G Bit NandFlash
      • Connectors:USB HS (mini / type A), USB FS (mini), Ethernet (RJ45)
      • All the idle I/O ports are accessible on the pin headers
      • 2.0mm pin header pitch, smaller size, easier to integrate into user system

      Note : please consider the EVK407I, which supports easily programing/debugging.


      What's On Board

      STM32F407IGT6 development board on board resource

      1. STM32F407IGT6:the high performance STM32 MCU which features:
        • Core: Cortex-M4 32-bit RISC
        • Feature: a full set of single-cycle DSP instructions
        • Operating Frequency: 168MHz, 210 DMIPS/1.25 DMIPS/MHz
        • Operating Voltage: 1.8V-3.6V
        • Package: LQFP176
        • Memories: 1024kB Flash, 192+4kB SRAM
        • MCU communication Interfaces:
          • 3 x SPI, 4 x USART, 2 x UART, 2 x I2S, 3 x I2C
          • 1 x FSMC, 1 x SDIO, 2 x CAN
          • 1 x USB 2.0 high-speed/full-speed device/host/OTG controller with dedicated DMA, ULPI and on-chip full-speed PHY
          • 1 x 10/100 Ethernet MAC
          • 1 x 8 to 14-bit parallel camera interface
        • AD & DA converters: 3 x AD (12-bit, 1μs, shares 24 channels); 2 x DA (12-bit)
        • Debugging/Programming: supports JTAG/SWD (serial wire debug) interfaces, supports IAP
      2. MIC2075-2, onboard USB FS power management device
      3. AMS1117-3.3, 3.3V voltage regulator
      4. K9F1G08U0E, 1G Bit NandFlash
      5. DP83848, Ethernet PHY
      6. MIC2075-1, onboard USB HS power management device
      7. USB3300, USB HS PHY
      8. Power supply switch, powered from 5Vin or USB connection
      9. Boot mode switch, for configuring BOOT0 pin
      10. Power indicator
      11. USB FS LED
      12. USB HS LED
      13. Reset button
      14. 8M crystal, MCU clock, enables the MCU run at higher speed by frequency multiplication
      15. 24M crystal, USB3300 clock
      16. 50M crystal, DP83848 clock
      17. 32.768K crystal, for internal RTC with calibration
      18. Ethernet connector
      19. USB FS mini connector
      20. USB HS mini connector
      21. USB HS type A connector
      22. MCU pins expander, VCC, GND and all the idle I/O ports are accessible on expansion connectors for further expansion
      23. USB OTG/HOST jumper
      24. VREF/VBAT jumper
      25. Ethernet I/O selection solder joint
      26. USB HS I/O selection solder joint
      27. PDR selection solder joint: 1.8-3.6V, -40~105℃ OR 1.7-3.6V, 0~70℃

      Package Content

      1. XCore407I development board x 1
      2. USB type A to Mini-B cable x 1
      3. Software CD x 1

      Note:
      XCore407I does NOT integrate programing/debugging interface.
      Mother board and accessories in the photos are NOT included in the price.


      Dimensions

      STM32 MCU core board dimensions


      Development Resources

      • Related software (KEIL etc.)
      • Examples in C
      • Schematic (PDF)
      • Development documentations

      Wiki: www.waveshare.com/wiki/XCore407I

      Waveshare Electronics
      WS-7696

      Specific References

      Customers who bought this product also bought:

      16 other products in the same category: