UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery
      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery
      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery
      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery
      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery

      UPS2 for C1/C1+ (Hardkernel) 3000mAh Lithium Polymer battery

      HK-UPS2-C1
      €70.44

      58.70 € tax excl.

      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery

      Quantity :
      OUT OF STOCK

      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery

      The UPS2 for C1 is designed specifically for the ODROID-C1/C1+

      Uninterrupted Power Supply is an electrical apparatus that provides emergency power to a load when the input power source, typically mains power, fails. The on-battery runtime of most uninterruptible power sources is relatively short but sufficient to start a standby power source or properly shut down the ODROID-C1/C1+

      It is equipped with a rechargeable 3,000mAh Lithium Polymer battery and a charger with a booster IC for 5V output. 
      When the AC power source fails, the UPS2 keeps supplying the power to the ODROID-C1/C1+ with the battery. There is a digital output pin to notice the battery low-level warning to the ODROID-C1/C1+ to trigger the shutdown process. And the AC power source available, UPS2 will supply the power to the ODROID-C1/C1+ again automatically.  It will significantly reduce the risk of data loss by sudden power-down.
      Full guide, schematics, PCB layout file and detail information is in our WiKi : http://odroid.com/dokuwiki/doku.php?id=en:odroid-ups2

      PACKAGE INCLUDES :

      - 3000mAh battery pack 
      - DC Plug Cable soldered UPS2 board 
      - 3pin jumper wire (11mm)
      - 4 x 20mm PCB spacers (Plastic)
      - 4 x 11mm PCB spacers (Metal)
      - 4 x 10mm PCB spacers (Plastic)
      - 5V/2A Power Supply

      JUMPER IT WITH ODROID-C1 :

      The AC_OK signal is connected to PIN#11(GPIO #88) in the 40pin header(J2) of ODROID-C1. 
      The BAT_OK signal is connected to PIN#13(GPIO #116). 
      The POWER_LATCH signal is connected to PIN#15(GPIO #115).
      If you connect it wrong way, you might burn your ODROID-C1 !

      DC Input Voltage / Current DC 4.8V ~ 5.4V / 2A minimum
      Battery Charging Time / Current 1.5 ~ 2 Hours / 2A maximum
      DC Output Current / Voltage Maximum 2A / 5V
      Battery 3,000mAh Lithium Polymer
      Connector : Molex 51021-0200
      Battery Life Cycle Carry out 400 cycle charging / discharging @ 20±5℃
      Integrated Protection PCB Over charge and discharge protection
      Estimated Running Time

       

      Hardkernel
      HK-UPS2-C1

      Specific References

      UPS2 for C1/C1+ (Hardkernel)  3000mAh Lithium Polymer battery

      UPS2 for C1/C1+ (Hardkernel) 3000mAh Lithium Polymer battery

      €70.44

      58.70 € tax excl.