Novinka

13.3inch e-Paper Display (B), E-Ink Display, 960×680 pixels, Red/Black/White,SPI, Partial Refresh (WS-27112)

13.3inch e-Paper Display (B), E-Ink Display, 960×680 pixels, Red/Black/White,SPI, Partial Refresh (WS-27112)

Name: 13.3inch e-Paper Display (B), E-Ink Display, 960×680 pixels, Red/Black/White,SPI, Partial Refresh (WS-27112)
Brand: Waveshare Electronics
SKU: WS-27112
Price: 176.94 EUR
Availability: PreOrder

Kód WS-27112

176,94 €

147.45 € bez DPH

Popis
Detaily produktu

13.3inch e-Paper Display (B), E-Ink Display, 960×680 pixels, Red/Black/White,SPI, Partial Refresh (WS-27112)

13.3inch E-Paper Display (B), E-Ink Display, 960×680 Pixels, Red / Black / White, SPI Communication, Partial Refresh Support, Optional For E-Paper Driver HAT

13.3″ E-Paper Display (B)

Low Power, Wide Viewing Angle, Paper-Like Effect Without Electricity

Ideal for price tags, shelf labels, industrial instruments...

13.3inch red / black / white e-Paper display, front view

Note: the e-Paper Driver HAT and accessories are optional, please refer to the Package Content for detailed part list

- Size13.3"
- Resolution960×680
- Viewing Angle>170°
- Display ColorRed / Black / White
- Grey Scale2

CommunicationSPI
Display PanelE-paper
ExperiencePaper-like
EnvironmentAmbient Light Required
Display TypePassively Reflective
RefreshingPartial Refresh Support

Version Options

13.3inch e-Paper (B)
raw display, without driver board

13.3inch e-Paper HAT (B)
with e-Paper Driver HAT

Features At A Glance

No backlight, keeps displaying last content for a long time even when power down
Ultra low power consumption, basically power is only required for refreshing
Comes with development resources and manual (driver board circuit diagram, examples for Raspberry Pi/Jetson Nano/Arduino/STM32)
Optional for e-Paper Driver HAT:
- With standard Raspberry Pi 40PIN GPIO extension header, supports Raspberry Pi series boards/Jetson Nano
- Adapting SPI interface for connecting with controller boards like Raspberry Pi/Jetson Nano/Arduino/STM32, etc.
- Onboard voltage translator, compatible with 3.3V / 5V MCUs

Specifications

OPERATING VOLTAGE	Raw display: 3.3V	GREY SCALE	2
OPERATING VOLTAGE	e-Paper Driver HAT: 3.3V/5V	GREY SCALE	2
INTERFACE	3-wire SPI, 4-wire SPI	PARTIAL REFRESH TIME	2.9s
DISPLAY DIMENSIONS	286.32 × 212.26 × 1.20mm	FULL REFRESH TIME	22s
DISPLAY SIZE	275.52 × 195.16mm	REFRESH POWER	75mW
DOT PITCH	0.287 × 0.287mm	STANDBY CURRENT	<0.01uA (almost none)
RESOLUTION	960 × 680 pixels	VIEWING ANGLE	>170°
DISPLAY COLOR	red, black, white

Advantages Of EINK

E-paper display utilizes microcapsule electrophoretic technology for displaying, the principle is: charged particles suspended in clear fluid will move to sides of microcapsule when electric field is applied, making the microcapsule become visible by reflecting ambient light, just as traditional printed paper.
E-paper display will clearly display images/texts under lamplight or natural light, requires no backlight, and features nearly up to 180° viewing angle. It is usually used as e-reader due to its paper-like effect.

Optional For E-Paper Driver HAT

Standard Raspberry Pi 40PIN GPIO Header, Compatible With Raspberry Pi Series Boards / Jetson Nano

13.3inch red / black / white e-Paper display, connecting with Raspberry Pi 5

Raspberry Pi 5 in the photo is NOT included.

Onboard SPI Control Interface
On E-Paper Driver HAT

For Use With Controller Boards Like Raspberry Pi/Jetson Nano/Arduino/STM32

e-Paper Driver HAT front view, interface introduction

VCC	3.3V/5V
GND	Ground
DIN	SPI MOSI pin
CLK	SPI SCK pin
CS	SPI chip selection, low active
DC	Data / Command selection (high for data, low for command)
RST	External reset, low active
BUSY	Busy status output
PWR	Power on/off control