STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)
      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)
      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)
      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)
      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)
      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)

      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)

      WS-22943
      27,99 €

      22.76 € bez DPH

      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)

      Množstvo:
      OUT OF STOCK

      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)

      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32

      STLINK-V3MINIE
      STM32 Debugger/Programmer

      Based On Arm Cortex-M STM32 32-Bit Microcontroller

      STLINK-V3MINIE-details-1.jpg

      The STLINK-V3MINIE is a stand-alone debugging and programming tiny probe for STM32 microcontrollers, portable and easy-to-use. Onboard JTAG/SWD interfaces for communicating with STM32 microcontroller, also provides a virtual COM port for the host PC to communicate with the target microcontroller through one UART.

      Features At A Glance
      • Tiny 15 mm × 42 mm stand-alone debugging and programming probe for STM32 microcontrollers
      • Self-powered through a USB Type-C connector
      • USB 2.0 high-speed interface
      • Probe firmware is updatable through USB
      • Support drag-and-drop Flash programming of binary files
      • Two color LEDs: communication, power
      • JTAG communication support up to 21 MHz
      • SWD (Serial Wire Debug) and SWV (Serial Wire Viewer) communication support up to 24 MHz
      • Virtual COM port (VCP) up to 15 Mbps
      • 1.65 to 3.60 V application voltage support
      Interface Introduction

      STLINK-V3MINIE-details-11.jpg
      Software Support
      STLINK-V3MINIE-details-13.jpg
      Hardware Support

      Support All STM32 Series MCUs With JTAG / SWD Interfaces

      STLINK-V3MINIE-details-3.jpg
      for reference only, STM32 MCU is not included.

      STLINK Series Selection Guide
      ITEMV3MINIEV3SETV2
      JTAG/SWD APPLICATION VOLTAGE 1.65V~3.6V 3V~3.6V 1.65V~3.6V①
      SWIM APPLICATION VOLTAGE N/A 1.65V~5.5V 1.65V~5.5V
      SWV SUPPORT YES②
      DEBUG INTERFACE multi multi③ 2
      LED INDICATOR two colors④
      ① ST-LINK/V2 and STLINK-V3MINIE support STM32 low-power devices.
      ② Only available for STM32 at present.
      ③ STLINK-V3SET features GPIO port besides the programming port.
      ④ Two colors LED indicates both power and communication.

      Connection Example

      STLINK-V3MINIE-details-5.jpgSTLINK-V3MINIE-details-7.jpg

      What's On Board
      STLINK-V3MINIE-details-intro.jpg
      1. USB Type-C connector
      2. Power LED indicator pad (LED is not soldered here)
      3. STM32F723 MCU
      4. BTB (board-to-board) card edge connector pads
      5. STDC14 debug connector
       
      1. COM LED Indicator
        The LED is blinking red: the first USB enumeration with the PC is taking place.
        The LED is red: the communication between the PC and STLINK-V3MINIE is established.(end of enumeration).
        The LED is blinking green/red: data are being exchanged between the target and the PC.
      Outline Dimensions
      STLINK-V3MINIE-details-size.jpg
      Resources & Services
      res_banner.png

      Balenie Obsahuje / Package Content

      STLINK-V3MINIE-details-pack.jpg

      Waveshare Electronics
      WS-22943

      Špecifické referencie

      STLINK-V3MINIE, In-Circuit Debugger And Programmer For STM32 (WS-22943)

      27,99 €

      22.76 € bez DPH