Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)
      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)
      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)
      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)

      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)

      WS-19838
      76,80 €

      64.00 € bez DPH

      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)

      Množstvo:
      OUT OF STOCK

      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)

      Dual Gigabit Ethernet Base Board Designed For Raspberry Pi Compute Module 4

      Dual Gigabit Ethernet Base For CM4

      Suitable For Evaluating The Raspberry Pi CM4 Or Being Integrated Into End Products

      Powerful Ethernet Capability

      CM4-DUAL-ETH-BASE-details-1.jpg
      Specifications
      CM4 SOCKET suitable for all variants of Compute Module 4
      ETHERNET Dual Gigabit Ethernet RJ45
      USB USB 3.2 Gen1 × 3
      PIN HEADER 40PIN GPIO header × 1
      HDMI HDMI × 2, supports 4K 30fps output
      DSI DISPLAY MIPI DSI display port × 1, 15pin 1.0mm FPC connector
      CSI CAMERA MIPI CSI-2 camera port × 2, 15pin 1.0mm FPC connector
      POWER INPUT 7V-36V
      FAN 5V/12V, allows speed adjustment and measurement
      RTC Real-time clock with battery socket and ability to wake Compute Module 4
      SD CARD SLOT MicroSD card socket for Compute Module 4 Lite (without eMMC) variants
      Connecting With Compute Module 4

      Standard CM4 Socket And Color-Coded Raspberry Pi 40PIN GPIO Header
      Suitable For Compute Module 4 Lite/EMMC Series Module

      CM4-DUAL-ETH-BASE-details-3.jpg
      Rich Interfaces

      Providing Interfaces Including: ETH/CSI/DSI/RTC/HDMI/Micro SD/USB

      CM4-DUAL-ETH-BASE-details-5.jpg
      What's On Board
      CM4-DUAL-ETH-BASE-details-intro.jpg
      1. CM4 socket
        suitable for all variants of Compute Module 4
      2. 40PIN GPIO header
        for connecting sorts of HATs
      3. RJ45 Gigabit Ethernet
        dual RJ45 Gigabit Ethernet, 10/100/1000M compatible
        ETHERNET 0: CM4 original ETH
        ETHERNET 1: USB extended ETH
      4. USB 3.2 ports
        3x USB 3.2 Gen1, for connecting sorts of USB devices
      5. HDMI connectors
        2x HDMI, supports 4K 30fps output
      6. CAM
        2x MIPI CSI camera ports
      7. DC power supply
        7~36V DC wide voltage range power input
      8. Dual LED indicators
        red: Raspberry Pi power indicator
        green: Raspberry Pi operating status indicator
      9. Micro SD card slot
        for connecting a Micro SD card with pre-burnt image (Lite variant ONLY)
      10. FAN header
        for connecting cooling fan, allows speed adjustment and measurement
      11. DISP0
        MIPI DSI display port
      12. USB SLAVE port
        for burning system image into Compute Module 4 eMMC variants
      13. RTC battery holder
        supports CR1220 button cell
       
      1. RTC interruption configuration
        PI-RUN: CM4 will reboot on RTC interruption
        GN-EN: CM4 powerdown on RTC interruption
        D4: D4 pin is triggered on RTC interruption
      2. IO-VREF selection
        set the CM4 IO logic level as 3.3V or 1.8V
      3. FAN power supply selection
        select 5V or 12V power to drive the fan
      4. System function configuration
        BT_DIS: Bluetooth disabled, for CM4 with antenna variant ONLY
        WiFi_DIS: WiFi disabled, for CM4 with antenna variant ONLY
        WP_DIS: boot mode switch, ONLY be used when NOT booted from eMMC or SD card
      5. RTC/FAN I2C bus selection
        SDA0/SCL0: I2C-10 is shared with CSI/DSI
        GPIO3/2: I2C-1 is shared with 40PIN header
      6. RTL8153
        USB Gigabit Ethernet chip
      7. EMC2301
        fan controller, allows fan speed adjustment and measurement
      8. VL805
        USB 3.0 HUB
      Outline Dimensions
      CM4-DUAL-ETH-BASE-details-size.jpg
      Application Example
      CM4-DUAL-ETH-BASE-details-7.jpg
      for reference only, CM4, display, cameras, and fan are NOT included.
      Resources & Services
      res_banner.png

      Package Content

      1. CM4-DUAL-ETH-BASE x1
      CM4-DUAL-ETH-BASE-3_220.jpg

      Waveshare Electronics
      WS-19838

      Špecifické referencie

      Dual Gigabit Ethernet Base Board Designed for Raspberry Pi Compute Module 4 (WS-19838)

      76,80 €

      64.00 € bez DPH