*replaced WS-14224* USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL
      *replaced WS-14224* USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL

      *replaced WS-14224* USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL

      WS-10406 (USB AVRISP PL)

      *replaced WS-14224* USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL

      Množstvo:

      USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL

      Supports AVR Studio 4 ONLY. Doesn't support AVR Studio 5/6 or higher versions.
      • AVR ISP Programmer, compatible with AT AVRISP from ATMEL
      • A professional low cost In-System Programmer. Programs FLASH , EEPROM, Fuses, and Lock Bit through USB

      Features

      • Programs all AVR Devices with ISP programming option, and certain 51 Devices
      • Programs both Flash and EEPROM
      • Supports Fuses and Lock Bit Programming
      • Based on STK500 firmware
      • upgradable to Support Future Devices
      • Adjustable Speed. Supports high speed programming up to 926K frequency
      • Quasi-USB interface to PC for Programming and Control (using PL2303TA, USB To RS232)
      • 3 optional cables to target board
      • Powered from USB bus. No need for Additional Power Supply

      Based on AT AVRISP
      - Compatible with AT AVRISP, easy to use, stable and reliable

      Based on STK500 firmware
      - Identified as AVRISP/STK500 in AVRStudio, high speed programming

      AVR Studio 4 firmware
      - Supports AVR Studio 4
      - NOT upgradable

      Supported software
      - AVR Studio or WINAVR(GCC) is used as front-end software
      - Supports the program files generated by IAR, ICCAVR, CVAVR

      Device Support
      - USB AVRISP supports all AVR 8-bit RISC Micro Controllers with ISP programming option. Support for new devices will be added through new versions of AVR Studio.
      - Supports AT86RF401/AT89S51/AT89S52

      Refer to AVRStudio 4.18, the following devices are supported:

      Classic Tiny* Mega* Other
      AT90S1200
      AT90S2313
      AT90S/LS2323
      AT90S/LS2343
      AT90S/LS2333
      AT90S4414
      AT90S/LS4433
      AT90S/LS4434
      AT90S8515
      AT90S/LS8535      		 ATtiny12
      ATtiny13
      ATtiny15
      ATtiny22
      ATtiny2313
      ATtiny24
      ATtiny25
      ATtiny26
      ATtiny44
      ATtiny45
      ATtiny461
      ATtiny84
      ATtiny85
      ATtiny861      		 ATmega48 ATmega48P
      ATmega8 ATmega88
      ATmega88P ATmega8515
      ATmega8535 ATmega16
      ATmega162 ATmeg164P
      ATmega165 ATmega165P
      ATmega168 ATmega168P
      ATmega169 ATmega169P
      ATmega32 ATmega324
      ATmega324P ATmega325
      ATmega325P ATmega3250
      ATmega3250P ATmega329
      ATmega329P ATmega3290
      ATmega3290P ATmega64
      ATmega640 ATmega644P
      ATmega645 ATmega6450
      ATmega649 ATmega6490
      ATmega128 ATmega1280
      ATmega1281 ATmega2560
      ATmega2561      		 AT86RF401
      AT89S51
      AT89S52
      AT90PWM2
      AT90PWM2B
      AT90PWM3
      AT90PWM3B
      AT90CAN32
      AT90CAN64
      AT90CAN128
      AT90USB162
      AT90USB646
      AT90USB647
      AT90USB1286
      AT90USB1287
      *Supports all low voltage versions of the devices with suffix of L/V, such as ATmega16L, ATmega48V

      Performance
      - High speed programs FLASH , EEPROM, Fuses, and Lock Bit
      - It takes only 5.5S to program a 12K program file with verification (AVRISP should be set to high speed 926K mode while the default frequency is 230K)

      Connects to PC
      - Uses a quasi-USB interface for communication with the front-end software (Probably AVR Studio)
      - Using PL2303TA, the USB To RS232 chip
      - The COM port is configurable, a PC could connects to several USB AVRISP at the same time

      Connects to target board
      The USB AVRISP connects to the target board through 3 optional cables. Depending on the existed connector on the target board, the cable has to be changed accordingly.
      - Standard 10-pin ISP Connector, Using 10-pin ISP cable
      - Standard 6-pin ISP Connector, Using 10-pin to 6-pin ISP cable
      - Custom ISP Connector, Using 10-wire multicolour custom connector cable
      The figure 1 and 2 shows the pinouts for the 10-pin and 6-pin ISP connectors.

        Figure 1. 10-pin ISP Connector
      pinouts for 10-pin ISP Connector      		 Figure 2. 6-pin ISP Connector
      pinouts for 6-pin ISP Connector

      Powered from USB bus
      - Draws power from the USB bus, No need for Additional Power Supply
      - The target board should be powered from Another Power Supply

      Downloads

      Development resources:user guide, software, etc.
      Wiki: www.waveshare.com/wiki/USB_AVRISP_PL

      Selection Guide

      ProgrammerISP-6PINISP-10PINISP CustomConnect to PCSpeedSupported AVR Studio
      USB AVRISP via adapter cable directly support via adapter cable USB TO COM (FT232RL) ★★★ 4 or lower version
      USB AVRISP PL via adapter cable directly support via adapter cable USB TO COM (PL2303TA) ★★★ 4 or lower version
      AT AVRISP - directly support - Serial port ★★★ 4 or lower version
      USB AVRISP XPII directly support via adapter cable via adapter cable USB（PDIUSBD12） ★★★★★ 4/5/6/7
      AT AVRISP MKII directly support via adapter cable - USB（PDIUSBD12） ★★★★★ 4/5/6/7
      Waveshare Electronics
      WS-10406 (USB AVRISP PL)

      Špecifické referencie

      USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL

      *replaced WS-14224* USB AVRISP PL, AVR ISP programmer (WS-10406) compatible with AT AVRISP from ATMEL